Small home improvement and repair projects are usually easy enough for the average do-it-yourselfer. However, there’s no such thing as a small project when it comes to your home’s electrical and wiring system. Working with electricity can be extremely dangerous, as even the slightest mistake can result in electrocution or lead to conditions which may result in an electrical fire. But as if safety wasn’t enough, there are actually lots more good reasons to hire a residential electrician in San Jose for your home’s rewiring project. Here are some of the most important.

Save Time
If your time is valuable, you can’t afford not to hire an electrician for your home rewiring project. Delta Electric can completely install new electrical wiring in a fraction of the time it would take on your own. Not only will this minimize the headache and frustration of having your home out of order, but it will also allow you to focus your energy elsewhere while a professional takes care of the electrical work.

Save Money
How could hiring an electrician possibly be less expensive than doing the work yourself? You may save on parts and labor by doing electrical work on your own, but you run the risk of paying a lot more when it’s discovered that you made a mistake. Even a minor error can require hundreds or even thousands of dollars in repairs, especially if that error lead to an electrical fire. Save your money and don’t take any chances; hire an electrician for all your electrical needs.

Stay Safe
Perhaps the most important reason to hire an electrician is the simple fact that working with electricity is incredibly dangerous. Handling your home’s electrical system should only be done by a trained, licensed, and experienced professional. Again, even the slightest error made on your own can result in tragedy.

A functioning circuit breaker in San Jose will prevent your appliances from using a dangerous amount of energy, but it cannot perform this task unless all of its circuits are working. The good news is that fixing the problem is relatively simple and straightforward. Watch this video clip for tips on replacing a faulty circuit.

The first step in replacing a faulty circuit is locating the breaker box. Once you have found your breaker box, open it up and turn off the main; this is a very important step that should never be skipped over. Unscrew and remove the panel and loosen the screw that holds the wire, then remove the circuit breaker itself. Now you can simply insert the new circuit breaker and tighten the screws, put the lid back on, and turn on the main breaker. Your circuit breaker should now be functioning at optimal capacity once again.

It is tempting to become frustrated with your circuit breaker in San Jose if it continues to trip, but it helps to keep in mind that you are on the same team. Your breaker box can keep you safe in the event that your appliances attempt to draw too much power through your electrical system; instead of hazardous consequences like fires, your system will shut down and recover. Keep reading if you would like to find out why your circuits keep tripping.

Overload
Your circuits trip in order to prevent excessive amounts of electricity from flowing and creating too much energy, and in many cases this occurs when someone attempts to use too many appliances at the same time . It is important to note that circuits and outlets are different things; just because your appliances are plugged into different outlets does not mean that they are operating on different circuits. Always consider the amount of power that any given appliance uses, and make sure you do not attempt to use a variety of other appliances at the same time. Sometimes circuits will trip in this manner because of loose connections, but you should always have a licensed electrician address these issues.

Ground Fault
If you are not using too many appliances at the same time, your tripping circuit problem may have to do with a ground fault. When a hot wire touches a ground wire, a ground fault occurs; the same can happen when the hot wire touches a metal outlet box. Diagnosing this problem is simple, as all you have to do is make sure that the hot wire is not touching either of these other elements. A ground fault is one example of a short circuit.

Short Circuit
When a hot wire touches a ground wire or metal outlet box, a ground fault occurs; this is because whenever a hot wire touches a hot or neutral wire, a short circuit results. Short circuits tend to be more severe than circuit overloads and can involve melted cords, so in this case it is wise to have a professional electrician take a look at your electrical system.

While there are many household problems that you may be able to diagnose and handle yourself, others tend to indicate the presence of a much bigger problem on the horizon. If you notice any problems that relate to your electrical wiring or circuit breaker in San Jose, a call to your local electrician should be placed immediately. As handy as you may be, electrical problems may compromise the safety of your home. Read on for a look at some of the top reasons to call an electrician.

Moving Into or Out of a Home
Relocating to a new house or apartment can be a positive and exciting experience, but you will need to take care of some things before you can sit back and relax. When you put your home on the market, it is important to make sure that it is as safe as can be and perfectly suitable for a new family. This means that any outlets or fixtures that have given you trouble in the past should be taken care of before moving so that they do not cause problems for the new homeowners. If you are on the other side and you are the one looking for a home, hiring your own electrician to scope it out is never a bad idea.

Issues with Your Light Bulbs
Whether you are at home or in your office building, take a moment to consider the lighting. Do the lights flicker? Have you seen one or more bulbs pop? Are some bulbs brighter than other bulbs of the same quality? If these questions bring memories to mind, your electrical system may not be working properly, and it may be showing through your lights.

Malfunctioning Outlets
There is no reason to accept the fact that an outlet simply does not work; you paid for your home or office, so you paid for the electrical wiring inside of it. If your outlets do not work the way they should, call an electrician and have the problem addressed. Keep an eye out for appliances that malfunction after consistently being plugged into the same outlet as well.

Operating a business is not a simple task, which is why delegation is one of the most important skills a manager can have. If you would prefer to save your energy to use in conducting your business, you may want to consider hiring an electrician in San Jose to make sure that your electrical wiring is safe and secure. Here is a brief overview of a few reasons your business may need electrical services.

Accidents involving electrical equipment can lead to very severe damages and even death, so it is important to ensure that you are working in a safe environment. You can achieve this assurance by having a trained electrician regularly inspect your workplace and identify any potential hazards. Your electrician can also make sure that your electrical system is functioning as efficiently as it should be, which can result in financial savings. An electrician that you hire for a safety inspection can also determine whether your electrical system should be rewired, and he or she can complete that process as well. In the event that you decide to add on to your business by physically constructing new buildings, it is wise to consult an electrician when deciding where to situate outlets and lighting.

It is easy to make a number of wiring mistakes that can lead short circuits, electrical shock, or even fire. The following article will review some of the common electrical wiring mistakes that can be avoided by adhering to professional electrician protocol. If you need help wiring your building, be sure to call a reliable commercial or residential electrician near San Jose .

Connecting to Outside Electrical Boxes
Always turn off the power at the main panel before working on electrical wiring . Avoid connecting wires outside of electrical boxes. If connections aren’t contained inside an electrical box, install one and connect the wires into it. Install the electrical box flush to the wall surface if the wall is made of combustible material. Cover the exposed combustible material with a box extension to prevent a potential fire hazard. Never overload a box with wires; install a larger box if needed.

Cutting the Wires Too Short
Wires that are too short make connections difficult and dangerous. The wires should protrude at least three inches from the box. An electrician can install a wire extension to your existing wires to strengthen the connection and make them safer.

Leaving Cables Unprotected
Never leave plastic-covered cable unprotected. If left exposed between framing members, plastic-sheathed cable is easily damaged. According to electrical code, cables must be protected in these areas, especially when the cables are run over or under ceiling or wall framing. Your electrician can protect exposed plastic-sheathed cable by installing a protective board. Cable that is not secured can become strained. Our electricians can connect loose cables to a metal box or to an approved cable clamp.

Using Loose Outlets and Switches
Loose switches and outlets are not only unattractive, but they’re dangerous. Outlets that are loosely connected will move around, causing the wires to loosen from the terminals. Loose wires tend to overheat, which creates a fire hazard. An electrician can fix loose outlets with rigid spacers that are designed to tighten the outlet connection.

Working on electrical wiring can be extremely dangerous if you are not a trained professional with proper safety gear. At Delta Electric, our certified electricians in San Jose have years of experience working with residential and commercial electric projects. To learn about why you should trust us with your aluminum wiring needs, read on.

Our electricians have been trained in aluminum wiring conversion and repair to ensure all electrical work is done safety and correctly. This, in turn, will give you a peace of mind that’s worth paying for. Delta Electric trains its electricians to conduct thorough inspections, so you can be sure that we are doing the most thorough job possible. Many insurance companies will reject a claim related to electrical wiring if there is not proof that the job was done professionally. We practice three methods of aluminum wiring repair. Call us today to learn more about our aluminum wiring services.

Adding a new light fixture is a great way to re-energize the mood and utility of a room. If you are interested in adding custom light fixtures, such as overhead lighting, you may find that professional installation by an electrician is recommended. To learn more about how to make your home more attractive with new lighting, read this article. And if you need a home electrician in San Jose to help you with your lighting installation and rewiring needs, call Delta Electric today.

Living Room
Install light for three of the four corners of your living room. One of the lights should be focused on an object, such as a piece a furniture, art, or plant life. Use a variety of lighting, including floor lamps, table lamps, and overhead fixtures . We recommend installing a three-way switch or dimmer for the living room to allow for a range of activities—from reading to watching movies.

Dining Room
Make the table the brightest area of the room. A chandelier or pendant above the table is a great way to do this, but you may want to set a 100-watt limit to avoid overpowering the table with light. Indirect lighting is an excellent touch in other parts of the room because it complements the room while promoting relaxation. Table lamps, sconces, and glass-cabinet lighting are effective at creating the perfectly subtle glow.

Bedroom
Create a cozy atmosphere by placing reading lamps or sconces next to the bed. If you hire an electrician to install recessed lighting or track fixtures, do not aim the light directly at the bed; instead, angle the lights toward the dressing area. Install low-wattage bulbs on lamps to create a tinted glow that resembles candlelight.

Bathroom
Sidelights, such as sconces on the side of the mirror, are ideal for bathroom lighting. Additional overhead lighting will fill in shadows in the bathroom, which makes it easier to clean. If your bathroom is particularly large, install light over the shower.

Wiring issues can cause problems both in older buildings and in new construction, and they are among the main reasons that homeowners and commercial property owners need electrical services in San Jose . Many wiring issues are also building code violations, because they can pose a danger to the occupants. If you suspect your home or building has any of the wiring issues below, contact a licensed electrician right away.

Uncovered Junction Box
Junctions are places where multiple wires are spliced together. All junctions should be covered by a junction box, which protects the wires from damage, prevents people from shocking themselves, and reduces the risk of fires. If you notice an uncovered junction box, have an electrician inspect the electrical wiring before installing a new cover.

Overwired Electrical Panels
Individual electrical panels can only have a limited number of circuits connected to them. Panels can become overwired gradually due to mistakes. For example, if property owners or non-certified electricians replace too many single-pole circuit breakers with tandem breakers that control two circuits, the panel will be overwired. To remedy this, you need to have a larger electric panel or a separate sub-panel installed.

Aluminum Wiring
Several decades ago, in the 1960s and 1970s, aluminum wiring was approved for commercial and residential use in California. However, in the intervening years, after many aluminum wires corroded and caused arcing and fires, authorities changed the codes. While some older buildings may be grandfathered in, it is still a good idea to replace aluminum wires with modern, safe copper wiring as soon as possible.

Knob and Tube Wiring
This very antiquated type of home wiring features wires that are sheathed not in plastic, but in cloth. Ceramic knobs hold the wires down, and ceramic tubes insulate them where they pass through the home’s framing. This type of wiring cannot be grounded, and overheated connections resulting from modern levels of current can easily melt the wires. You should have an electrician replace any knob and tube wiring with modern copper wiring as soon as possible.

Many older buildings, both residential and commercial, need rewiring near San Jose . The aluminum wiring that was widely used in the 1960s and 1970s is not safe for use in today’s homes, with their increased use of electricity, and the even older style of knob and tube wiring can be quite unsafe as well.

Pay close attention to electrical function in your home or commercial property to determine if you need a licensed electrician. Flickering lights, frequent circuit breaker trips, and other seemingly minor problems can all indicate faulty or outdated wiring. Also, if you find that you do not always have enough available outlets and you are using power strips or extension cords, it might be safer to rewire the building and increase the number of receptacles. Excessive sparking or a low hum coming from your electrical panels also point to bad wiring that needs to be replaced. If you notice any of these symptoms, schedule an electrical safety inspection with a licensed electrician so he can examine your wiring and recommend a fix.